Atemschutzmaske 9310-3M Angebote
-
Filter gegen organische Dämpfe 3M™ 6055PRO1, Schutzklasse A2
- Preis nur
- 19,95 €
- Entfernt:
- 12,15 km
Die beste Atemschutzmaske nützt nichts, wenn die Filter gesättigt sind. Mit diesem Filterset tauschst Du sie im Handumdrehen aus. Produktmerkmale der Filter 6055PRO1 mit Schutzklasse A2 von 3M™ Darum solltest Du zugreifen: Mit diesen Filtern für das 3M™-Farbspritzmaskenset A2/P2 ersetzt Du die verbrauchten und kannst sofort weiterarbeiten. Die Gasfilter bieten Dir effektiven Schutz vor gesundheitsgefährdenden Gasen und Dämpfen, wenn Du beispielsweise mit lösemittelhaltigen Farben, Klebstoffen und Reinigungsmitteln arbeitest. Gut sehen kannst Du trotzdem immer noch, denn durch die einzigartige Trapezform wird das Sichtfeld nicht eingeschränkt. Die Filter eignen sich für Masken der Serien 6000, 6500 und 7000 von 3M™. Unnötig zu erwähnen, dass sie selbstverständlich nach europäischen Normen geprüft und zugelassen wurden. Deshalb haben sie die CE-Kennzeichnung 0086 (EN 14387:2004+A1:2008 A2). Allergiker werden sich darüber freuen, dass das Produkt kein natürliches Latex enthält. Festgenagelt: Mit diesen Ersatzfiltern ist Deine Atemschutzmaske schnell wieder einsatzbereit.
- Erhältlich bei:
- Hornbach
-
Wassertranferdruck-Folie Premium CCP-008 50 cm breit (Meterware)
- Preis nur
- 7,95 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Premium CCP-010 blaugrün 100 x 50 cm
- Preis nur
- 7,95 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Premium CCP-009 rot 100 x 50 cm
- Preis nur
- 7,95 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Premium CCP-006 perlmutt 100 x 50 cm
- Preis nur
- 7,95 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-002-04 blau 100 x 50 cm
- Preis nur
- 7,95 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-003 grün 100 x 50 cm
- Preis nur
- 7,95 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-003-05 grau 100 x 50 cm
- Preis nur
- 6,90 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-003-06 grün 100 x 50 cm
- Preis nur
- 6,90 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-004-03 grau 100 x 50 cm
- Preis nur
- 6,90 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-005 beige 100 x 50 cm
- Preis nur
- 6,90 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-004-01 beige 100 x 50 cm
- Preis nur
- 6,90 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-012 grünlich 100 x 50 cm
- Preis nur
- 7,95 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-013-02 grünlich 100 x 50 cm
- Preis nur
- 7,95 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach
-
Wassertransferdruck Folie Tarn CA-NR-013-03 grünlich 100 x 50 cm
- Preis nur
- 7,95 €
- Entfernt:
- 12,15 km
Der Wassertransferdruck ist ein Oberflächenbeschichtungsverfahren zum Aufbringen unterschiedlicher Muster und Dekore auf dreidimensional geformte Objekte. Die Dekore sind hierbei auf einen speziellen wasserlöslichen Polyvinylalkohol-Film gedruckt und sind die Basis für den Lackiervorgang. Mit diesem Verfahren können Sie alle lackierbaren Oberflächen wie Steckdosenrahmen, Briefkästen, WC-Sitze, Werkzeuge, Türdrücker etc. individuell mit vielen verschiedenen Dekoren selbst gestalten. Probieren Sie es selbst aus. Gebrauchsanweisung genau durchlesen und loslegen! Nachfolgend fassen wir die Verarbeitungs-Schritte zusammen: Wie beim herkömmlichen Lackieren sind auch hier die zu beschichtenden Teile vorab zu reinigen (wir empfehlen einen Silikonentferner) und anzuschleifen. Für die Verarbeitung empfehlen wir Handschuhe und eine Atemschutzmaske zu verwenden. Danach wird der Untergrund mit einem Haftgrund-Spray und einem Basislack-Spray im gewünschten Grundfarbton vorbehandelt. Je nach Grundfarbton des Basislack´s ändert sich die Wirkung der Wassertranserdruckfolie: z.B. mit einem Basislack weiß wirkt die Folie durch den weißen Untergrund heller. Danach kann die Verarbeitung mit der Folie beginnen. Die Folie dazu je nach Größe des Lackierobjektes zuschneiden und mit dem Dekor nach unten in ein ca. 30 °C warmes Wasserbecken legen. Es empfiehlt sich die Ecken vorab mit Klebeband einzufassen. Das erleichtert die spätere Verarbeitung. Nach ca. 90 Sekunden die Folie mit dem Aktivator-Spray besprühen bis die Folie glänzt. Nach ca. 5 bis 10 Sekunden das zu lackierende Teil mit der schmalen Seite zuerst auf die Folie legen und dann komplett mit der Folie unter Wasser drücken. Danach das lackierte Objekt aus dem Wasser holen, überschüssige Folie mit fließendem warmen Wasser abspülen und trocknen lassen. Damit die Oberfläche widerstandsfähig wird, das Objekt nach 24 Stunden mit Klarlack-Spray überziehen. Für die Verarbeitung benötigen Sie: • Wassertransferdruckfolie im gewünschten Design zum Lackieren • Silikonentferner zum Reinigen • Haftgrund-Spray zum Grundierung • Basislack-Spray für die Basislackierung • Aktivator-Spray zum Aktivieren der Wassertransferdruckfolie • Klarlack-Spray zum widerstandsfähigen Beschichten nach dem Trocknen Alle Lackierprodukte können Sie bei uns jeweils einzeln beziehen oder im Set. Das Starter-Set beinhaltet Silikonentferner, Haftgrund-Spray, Basislack-Spray, Aktivator, Klarlack-Spray, Handschuhe und Cuttermesser. Die Wassertransferdruckfolie wählen Sie bitte noch zusätzlich nach Ihrer gewünschten Optik aus.
- Erhältlich bei:
- Hornbach